Envío gratuito en EE. UU. hasta 10 libras | Política de devolución sin complicaciones | Soporte al cliente 24/7

¡Compra ahora y paga después con Shop Pay!

Seagate Exos vs WD Ultrastar: Best Enterprise HDD?

Seagate Exos and WD Ultrastar enterprise hard drives side by side for comparison

Orange Hardwares |

The Seagate Exos and WD Ultrastar are well-established enterprise hard drive lines designed for high-capacity storage environments. This comparison examines the Seagate Exos X16 and X18, as well as the WD Ultrastar DC HC520 and HC550. These models share several specifications, but capacity, cache size, and performance differ by generation and configuration.

If you're comparing the Seagate Exos X18 18TB with the WD Ultrastar HC550 18TB, focus on how each model matches your storage requirements. This guide addresses specifications, capacity options, interface differences, and purchasing considerations for enterprise HDDs.

Compare the Exos and Ultrastar Models

The table presents representative models from both product families. The specifications pertain to the configurations displayed. Other capacities and model variants might vary.

Model Capacity Cache Interface Workload Rating MTBF Manufacturer warranty
Seagate Exos X16 14 TB 256 MB SATA 6 Gb/s or SAS 12 Gb/s Up to 550 TB/year 2.5 million hours 5-year limited
Seagate Exos X18 18 TB 256 MB SATA 6 Gb/s or SAS 12 Gb/s Up to 550 TB/year 2.5 million hours 5-year limited
WD Ultrastar DC HC520 12 TB 256 MB SATA 6 Gb/s or SAS 12 Gb/s Up to 550 TB/year 2.5 million hours 5-year limited
WD Ultrastar DC HC550 18 TB 512 MB SATA 6 Gb/s or SAS 12 Gb/s Up to 550 TB/year 2.5 million hours 5-year limited

The HC550 offers twice the cache of the X18. However, cache size alone does not ensure greater speed in every application. 

The published maximum sustained transfer rates are similar. The 18 TB HC550 reaches up to 269 MB/s, while the X18 reaches 270 MB/s.

The reliability figures also require context. 

Seagate specifies the X18 MTBF under defined enterprise operating conditions, whereas WD describes the HC550 MTBF and annualized failure rate as projected values. Both refer to statistical reliability across a population of drives and do not indicate the expected lifespan of any individual unit.

Recommended: WD hard drive colors explained, from Blue to Gold

Choose a Capacity for Your System

Capacity determines storage density and how many drive bays a system needs and how long an array takes to rebuild following a failure. 

Evaluate the models on offer against the usable storage you actually require, rather than selecting on capacity alone.

14TB Drives

For systems that do not require an 18 TB drive, the Seagate Exos X16 provides 14 TB. It can also serve as a replacement for an existing drive in storage configurations that support this model. Customers looking to buy a Seagate Exos X16 14TB can compare it with other enterprise drives in the same capacity range.

16TB Drives

The 16TB versions of the Exos X18 and Ultrastar DC HC550 provide an intermediate capacity option. Compare their interface, sector format, condition, and warranty before choosing a refurbished unit. Its capacity sits between the 14 TB and 18 TB models.

18TB Drives

Both the Exos X18 and the Ultrastar HC550 reach 18 TB. This higher density lowers the number of drives required to achieve a given raw capacity.

A larger drive also requires more time to rebuild, and that duration depends on the RAID level, controller, workload, and volume of data being reconstructed. Array protection and spare-drive planning should take this into account.

20TB Drives

The Seagate Exos X20 and WD Ultrastar DC HC560 exceed the 18 TB models and are suited to deployments requiring greater density without additional drive bays. Buyers intending to purchase a 20 TB enterprise hard drive should compare the newer generation's specifications with their requirements, as features from earlier models may not be retained.

Recommended: Biggest HDDs and SSDs you can buy today

Check SAS and SATA Compatibility

SATA drives use a 6 Gb/s interface and are compatible with numerous NAS and server platforms. SAS drives use a 12 Gb/s interface and require a controller or backplane that supports SAS. In general, a SAS controller can operate SATA drives, but a SATA-only controller is unable to operate a SAS drive.

SATA is suitable for systems that support SATA drives and do not require features unique to SAS. SAS is suitable for platforms that require SAS connectivity, dual-port operation, or other SAS capabilities.

If you need to buy an 18TB SAS HDD, verify that the server is equipped with a SAS-capable controller and backplane. Also verify whether the platform supports the drive's SAS generation and operating configuration, especially when the drive is being added to an existing storage array.

The sector format is also important. These drive families offer 512e and 4Kn variants, while certain SAS configurations support additional sector sizes. Older RAID controllers, operating systems, and storage applications may not support every format, so verify the required sector size before you replace a drive or add a new model to an array.

Compare Enterprise HDD Prices

Enterprise HDD pricing varies according to stock, condition, capacity, and demand. Any WD Ultrastar DC HC550 price reflects a specific point in time rather than a permanent market value. Compare listings that align on capacity, interface, sector format, encryption option, and warranty coverage.

For recertified Exos drive prices, rely on listings with equivalent capacities and configurations. Interface, condition, warranty coverage, and included services all influence the final cost, so evaluate the full quoted price instead of the advertised drive price.

Calculate Cost Per Terabyte

Cost per terabyte (TB) provides a consistent way to compare enterprise HDD pricing across different capacities.

Cost per TB = Total Purchase Price ÷ Drive Capacity

For example, an 18 TB drive priced at $360 comes to $20 per TB. Apply the same calculation to each candidate, then factor in shipping, taxes, and any additional testing costs.

The result is only meaningful when the drives match in specifications and condition.

Evaluate Refurbished and Recertified Drives

The terms refurbished and recertified do not indicate how thoroughly a drive was inspected or whether it is appropriate for production use. Operating history and test records do provide that information. Prior to purchasing, request the following information from the seller:

  • Whether the drive has been subjected to diagnostic testing and whether the seller screens for read or write errors.
  • The available SMART data and power-on hours, which show how the drive has been used.
  • The condition grade: refurbished, recertified, or another used category.
  • The duration of the warranty, who is responsible for it, and the replacement or refund procedure if the drive fails.

For a WD Ultrastar refurbished with warranty listing, determine whether the seller or the manufacturer supplies the coverage. The five-year limited warranty stated in manufacturer datasheets applies to eligible new products and should not be presumed to cover refurbished stock.

Once the inspection and compatibility checks are complete, test the drive in its intended environment before deploying it for production workloads. During initial use, monitor SMART status and operating behavior so that problems are identified early.

Plan a Bulk Enterprise HDD Purchase

Bulk enterprise HDD purchases require more coordination than ordering a single replacement drive. Differences between batches can affect drive configuration, documentation, and deployment consistency. Finalize the requirements before confirming a bulk order.

Request that the supplier verify the available quantity and confirm whether the drives originate from the same production or refurbishment batch. Before ordering, reach agreement on model numbers, interface configurations, quantities, and the delivery schedule.

Upon delivery, verify model and serial numbers against the order. Document each drive's installation date, system assignment, and warranty details. These records assist IT teams in tracking deployed units and planning replacements. Maintaining compatible spare drives on hand minimizes delays when a drive fails.

Match the Drive to Your Storage Requirements

Use this quick checklist to narrow down your pick before you compare listings.

How to Choose Your Enterprise HDD
Four quick checks to narrow down the right Exos or Ultrastar drive.
1
Pick the interface
Does your controller and backplane support SAS?
Yes: SAS 12 Gb/sSAS platforms, dual-port use.
No: SATA 6 Gb/sMost NAS and server platforms.
2
Choose the capacity
How much usable storage per drive?
12 to 14 TBUltrastar HC520 or Exos X16.
16 to 18 TBExos X18 or Ultrastar HC550.
20 TBExos X20 or Ultrastar HC560.
3
Decide on condition
New or refurbished?
New5-year limited warranty on datasheets.
RefurbishedAsk for SMART data, tests and seller warranty.
4
Confirm the sector format
Does your controller, OS and array support it?
512eSafer for older controllers.
4KnOnly if your whole stack supports it.

The Exos X18 and Ultrastar HC550 offer comparable 18 TB capacities and very similar sustained transfer rates, while the HC550 provides the larger cache. The X16 and HC520 continue to be viable choices for deployments with lower capacity needs.

The selection should be guided by storage architecture and workload rather than brand preference.

In the case of refurbished or recertified purchases, documented condition and warranty coverage likewise determine suitability.

Frequently Asked Questions

Q: Does the Seagate Exos or the WD Ultrastar come with a longer warranty?

A: For the new models compared here, neither offers a longer published warranty. Both manufacturers offer a five-year limited warranty. Refurbished and recertified drives may come with different coverage, so verify the seller's warranty period and claims process before placing an order.

Q: Which model has the higher MTBF, the Exos or the Ultrastar?

A: For the models compared here, both publish an MTBF of 2.5 million hours. WD states that the HC550 figure is projected under specified operating conditions. MTBF is a statistical measure of reliability derived from a population of drives and does not predict the lifespan of any individual unit.

Q: Which drive offers the better annualized failure rate?

A: For the models discussed, both manufacturers publish an AFR of 0.35%. However, the figures are based on different stated operating conditions, and WD describes its HC550 rating as projected. AFR estimates the proportion of drives expected to fail each year under specified conditions. It does not predict when a particular unit will fail.

Q: Is the Seagate Exos or the WD Ultrastar less expensive per TB?

A: Neither brand is consistently less expensive across all capacities and configurations. Prices vary with the model, interface, condition, seller, and warranty. Compare listings with equivalent specifications and calculate the cost per terabyte to evaluate relative value.

Q: What workload rating do Exos and Ultrastar carry? 

A: The models discussed here carry workload ratings of up to 550 TB annually. Weigh that limit against the annual drive activity you anticipate, and check the manufacturer's operating conditions. A workload rating reflects the volume of data a drive is engineered to process each year, rather than a guaranteed service life.

Escribir un comentario

Tenga en cuenta que los comentarios se tienen que aprobar antes de que se publiquen.

Need Assistance?

Request a quote for exclusive pricing or bulk orders.

By providing a telephone number and submitting this form you are consenting to be contacted by SMS text message. Message & data rates may apply. You can reply STOP to opt-out of further messaging.